- New
Reference: 144.405.003
ULTRA RACING valves for POLINI MBK 51 / PEUGEOT 103 housings Incorporated support
HYPER RACING valves with diffuser, bonded, single-leaf for POLINI 103, 51, MINICROSS POLINI, APE ...
Banner
The intake pipe C. BOUCHET printed in 3D in a specific material for good holding in time. This pipe must be mounted with caution, with a torque of 4.5 NM with a dynamometer tool and mounted with joint paste ATHENA ATHESIL!
This pipe designed by a motorist for performance, has a diffuser entering the valves to improve the intake! It is cubited so as to take the carburation to the side of the machine. It comes with a soft sleeve and collars, as well as its screws.
Even if the diameter is not optimal, the pipe can receive carburettors 15 to 17.5mm also, of the type PHBG and POLINI CP!
This intake pipe is made to mount PHBG carburettors and POLINI CP 19 to 21mm flexible mounting on:
MBK 51 / AV10 MOTOR with housings POLINI
PEUGEOT 103 with housings POLINI incorporated media
*Warning, don't get on crankcases POLINI without incorporated supports of PEUGEOT 103!!!
**Warning, on PEUGEOT 103 SPX, RCX, MVX and CLIP, there is very little room! It is possible that this does not pass and that the pipe POLINI Flexible!!! On SP, MV... It is also possible to change the swinging arm because there is very little room!!!
Reference: 144.405.003
HYPER RACING valves with diffuser, bonded, single-leaf for POLINI 103, 51, MINICROSS POLINI, APE ...
Reference: 516867
A shorter pipe for a better venturi effect. It will be perfect with a 19 to 21mm carburettor.
Reference: 02 6488B
A pipe that mounts very well with a PHBG from 17.5 to 21mm. This pipe is corrected and revised for better distribution.
Reference: pipe CBE 90° 103 carters malossi 28
3D printed EPC pipe for housings MALOSSI on 103, EUROCILINDRO on MBK 51...
Reference: 1403
A pipe which will be perfect accompanied by a carburettor PHBG 19 to 21mm. This pipe is blasted with a good finish to avoid the rebound of gases.
Reference: 928.270.006
POLINI pipe for THOR engine or adaptation on PEUGEOT 103 / MBK 51 requiring an elbow admission!
Reference: 02 6487B
The best to accompany a 15 or 16mm SHA carburetor on your 103!
Reference: 56251.05
Ideal with a carburettor PHBG 19 to 24mm and achieve maximum performance! Model "finned" for mob Peugeot 103 SPX, RCX ...
Reference: pipe_coudée_carter_polini_cbe_PHBG
Pipe POLINI flexible 21mm for mopeds with crankcases POLINI!
Reference: pipe_coudée_carter_polini_cbe_PWK
Pipe POLINI flexible 24-28mm for mopeds with crankcases POLINI!
Reference: 144.270.001
Flexible polini pipe 21mm for mini-moto and cross 2T POLINI, or mounting on POLINI crankcases with PEUGEOT 103 and MBK 51 supports!
Reference: 215.0225
Very good POLINI intake pipe for fitting 17.5 to 21mm PHBG carburettors.
Reference: 215.0227
High quality intake pipe for mounting PHBG carburetors from 17.5 to 21mm.
Reference: 02 1690B
An intake pipe adapted for a carburettor of 15mm or 16mm SHA on PEUGEOT 103!
Reference: 1402
An intake pipe with a good finish that will allow you to mount your carburetor Ø14 to 16mm while gaining power.
Reference: pipe CBE 90° 103 carters malossi 21mm
3D printed EPC pipe for housings MALOSSI on 103, EUROCILINDRO on MBK 51...
Reference: 496075
Ideal in case of breakage or wear your old room.