- New
Reference: 144.405.003
ULTRA RACING valves for POLINI MBK 51 / PEUGEOT 103 housings Incorporated support
HYPER RACING valves with diffuser, bonded, single-leaf for POLINI 103, 51, MINICROSS POLINI, APE ...
Banner
The intake pipe C. BOUCHET printed in 3D in a specific material for good holding in time. This pipe must be mounted with caution, with a torque of 4.5 NM with a dynamometer tool and mounted with joint paste ATHENA ATHESIL!
This pipe designed by a motorist for performance, has a diffuser entering the valves to improve the intake! It is cubited so as to take the carburation to the side of the machine. It comes with a soft sleeve and collars, as well as its screws.
Even if the diameter is not optimal, the pipe can receive carburettors 15 to 17.5mm also, of the type PHBG and POLINI CP!
This intake pipe is made to mount PHBG carburettors and POLINI CP 19 to 21mm flexible mounting on:
MBK 51 / AV10 MOTOR with housings POLINI
PEUGEOT 103 with housings POLINI incorporated media
*Warning, don't get on crankcases POLINI without incorporated supports of PEUGEOT 103!!!
**Be careful, do not mount with a kick box on the MBK 51, and prevent the side hoods from resting!
Reference: 144.405.003
HYPER RACING valves with diffuser, bonded, single-leaf for POLINI 103, 51, MINICROSS POLINI, APE ...
Reference: 928.270.006
POLINI pipe for THOR engine or adaptation on PEUGEOT 103 / MBK 51 requiring an elbow admission!
Reference: 02 1690B
An intake pipe adapted for a carburettor of 15mm or 16mm SHA on PEUGEOT 103!
Reference: 496075
Ideal in case of breakage or wear your old room.
Reference: 02 5035B
The best to repair or modify the size of your MALOSSI valve boxes on your PEUGEOT 103 or MBK 51.
Reference: 215.0225
Very good POLINI intake pipe for fitting 17.5 to 21mm PHBG carburettors.
Reference: pipe_droite_carter_polini_cbe_PHBG
Pipe POLINI flexible 21mm for mopeds with crankcases POLINI!
Reference: 02 2083B
The top of the intake pipe to put your PHBG 17.5mm to 21mm on your 103.
Reference: pack_pipe_malossi_AM6_DERBI_90°
MALOSSI pipe for adaptation on PEUGEOT 103 / MBK 51 requiring an angled admission! Center distance am6 / DERBI
Reference: 215.0226
Intake pipe ideal for fitting SHA 15 or 16mm carburettors.
Reference: 02 6489B
A pipe specially designed for flexible assemblies. This pipe was specially created for the competition. It is therefore mounted with a flexible PHBG carburetor from 15 to 21mm.
Reference: 1399
Ideal in case of breakage or wear of your old part.
Reference: 02 6238B
A pipe specially designed for MALOSSI housings. It is very short with good diffusion, micro-blasted and with horizontal bars to avoid any gas rebounds. Clearly a very well worked pipe which will be accompanied by a VL6 valve box or other AM6 valve and a 21mm carburetor.
Reference: 365641
A shorter pipe for better venturi effect. This pipe is the highest end of the market. It will be perfect with a carburetor 19 to 21mm.
Reference: pipe CBE 90° 103 carters malossi 21mm
3D printed EPC pipe for housings MALOSSI on 103, EUROCILINDRO on MBK 51...
Reference: 1402
An intake pipe with a good finish that will allow you to mount your carburetor Ø14 to 16mm while gaining power.