Reference: 01486_72
Main Jet For DELLORTO Carburetor Small Pitch 5mm Thread 8mm Length Genuine (INC Certified)
Certified DELLORTO INC! Choose real DELLORTO quality!
Banner
Reference: 01486_72
Certified DELLORTO INC! Choose real DELLORTO quality!
Reference: 09475_40
The replacement and adjustment bushel for your PHBG carburettors, 30° or 40° cut more aggressive choices!
Reference: 53024
The complete richness screw for your PHBG carburettors!
Reference: 09444_00
The replacement tank at low prices for your DELLORTO carburettors.
Reference: 09506
Bar, axle, float holding rod for DELLORTO carb.
Reference: 53027_00
The idle screw with its spring for your PHBG carburettors!
Reference: 09595_20
Needle, essential for adjustments or at the slightest wear, irregularity.
Reference: 09450
The replacement float for your carbs, ideal in the event of a fuel leak!
Reference: 09596_00
Ideal in case of loss or breakage.
Reference: 02838_00
Ideal in case of problem, breakage or loss of your old part!
Reference: 53002_00
A pack to switch your PHBG carburettors choke lever to cable choke!
Reference: 14958_00
Ideal in case of loss or breakage of your old support, bushel socket.
Reference: 52526_77
Ideal for refurbishing your standard PHBG or racing black edition.
Reference: 09597_00
The valve spring for your carbs, ideal when the handle returns badly or in the event of loss, wear, breakage...
Reference: 01488_30
Idle jet for PHBG and PHBD carburettors, to obtain a correct idle when the bushel is at the bottom! With a good reaction to the opening bushel!
Reference: 09654_264
Essential part for the proper functioning of your carburettor, ideal in case of wear or breakage...
Reference: 09501_40
Essential part for the proper functioning of your carburetor, several sizes to choose from to fine-tune your settings!
Reference: 09511_254
Essential part for the operation of your carburetor, ideal in case of wear or breakage ...
Reference: 09779_00
Essential part of your carburettor PHBG for better mixing oil / petrol! Not deep model for jet small step 5mm.
Reference: 10431
The bowl bottom also called anti-emulsion washer ... Indispensable for the proper functioning of your carburetor and oil / gasoline mixing!
Reference: 09538_00
Ideal to pass your choke cable pull or to repair your PHBG!
Reference: 09812
A mass-machined brass cap for your carburetors with aluminum tank or racing black edition!
Reference: 09811_00
The aluminum racing tank, mounts on all PHBG carburettors, to remove your jets faster, drain faster and get more strength!
Reference: 01476_00
The original cap of all DELLORTO carburetor. Perfect for any loss or breakage of your old cap.
Reference: 01104_00
Arises directly in the plug cover, also available in angled with adjuster.
Reference: 4224-82
A tulip which increases the venturi effect therefore the efficiency of your engine.
Reference: 1285
Ideal in case of leakage for a good quality repair at low price.
Reference: 213458
A necessary part for the proper functioning of your carburetor.
Reference: 1297
A small spring that is important. Ideal for lost or worn for a refurbishment cost.
Reference: 1280
Ideal for refurbishment or for loss.
Reference: 1282
Ideal for lost or just for a refurbishment without spending too much.
Reference: 1263
The tension adjuster which is placed at the end of your tubes.
Reference: 1298
The little room in which hangs the starter cable.
Reference: 4477.62
The ring which seals and tightens your intake pipes with your RIGID PHBG!
Reference: 121692
The counter nut that locks your cable tension adjuster on DELLORTO carburettor.
Reference: 129517
The only wealth screws for your PHBG!
Reference: 2707
The idle screw without its spring for your PHBG!
Reference: 16962_00
The replacement cover single screw for your carburettors DELLORTO PHBG Racing Red and Black Edition.