- -8%
Reference: 11 3593
Pack spare seal for kit Ø43mm 65cc Cast iron CVF MALOSSI on PIAGGIO CIAO
The spare seal pack for your 43mm cast iron on PIAGGIO CIAO!
Banner
Here is the complete kit 65cc MALOSSI Ø43mm cast iron mounted two rectangular segments of type 1.5mm thick cast iron. Select the template axis 10mm or 12mm according to your crankshaft.
This cylinder is really the most work (CVF from MALOSSI for connoisseurs) it has 7 transfers and famous architecture CVF with doubled lights. The diagrams are low enough. The combustion chamber is blasted finish and high compression hemispherical, cylinder head also offers the possibility to install a decompressor.
The materials used are of the highest quality, this high engine will offer completely different performances of origin, as a couple of baths that power. The piston is also type CVF cast aluminum with high silicon content.
With this kit it will take at least mounted you a carburetor 13mm machined so it will take you to the original intake pipe and crankcase and crankshaft if you have the original casings, whereas if you have the cards MALOSSI you will have no change to be made.
With its 43mm diameter intended for the original race crankshaft 43mm CIAO, a so-called square stroke is obtained! Either maximum performance!
Kit accompanied by a large carburation (13mm), a reinforced crankshaft, reinforced bearings play C3, candle racing colder than the original, and a racing exhaust.
The pack contains:
Cast iron cylinder CVF
Cylinder head high compression decompression possibility
Piston pin 10 or 12mm depending on the choice
Axis 10 or 12mm depending on the choice
Stock C 10 or 12mm depending on the choice
Aluminum cylinder head gasket
Paper base seal
1.5mm thick cast segments
Instructions in Italian only and downloadable here
stickers MALOSSI
Spare parts:
Cylinder head
+ Cylinder piston without cylinder head axis 10mm
+ Cylinder piston without cylinder head axis 12mm
Piston pin clips with C Ø10mm
Piston pin with clips in G Ø10mm
Piston pin clips with C Ø12mm
Piston pin with clips in G Ø12mm
Piston Type G Ø10mm Clips
Piston Type C Ø10mm Clips
Piston Type G Ø12mm Clips
Piston Type C Ø12mm Clips
Piston shaft Ø10mm
Piston shaft Ø12mm
segments
Pack joints
Itself on:
PIAGGIO BRAVO 50
PIAGGIO BOSS 50
PIAGGIO GRILLO 50
PIAGGIO SI 50
PIAGGIO Superbravo 50
PIAGGIO CBA 50
and other models.
Optional we offer a preparation course 1, this preparation is a modification of the exhaust port by increasing the charts and improvement of the duct, it increases the cylinder performance. Improved bottom skirt is also included in the amendment. Allow a little extra time for this preparation!
Reference: 11 3593
The spare seal pack for your 43mm cast iron on PIAGGIO CIAO!
Reference: 23 3829BA
Ideal in case of loss or breakage of your old axis and piston clips.
Reference: 35 5268
Ideal for back compression, cheaply.
Reference: 34 4937.A0
Ideal for maintenance, breakage, wear .... The piston MALOSSI CVF 43mm 65cc cast! On PIAGGIO Ciao.
Reference: 3118709
The CVF piston cylinder 65cc 43mm for PIAGGIO CIAO without cylinder head!
Reference: 38 3267
The Ø43mm cylinder head for 65cc aluminum or cast iron MALOSSI or other kits on PIAGGIO CIAO GRILLO, BOSS, SI, BRAVO ...
Reference: 34 6898.B0
Ideal for maintenance, breakage, wear .... The MALOSSI CVF 43mm 65cc cast iron piston! On PIAGGIO Ciao.