
Reference: 060609435
Bi-piston segments Ø43,5mm for 70cc kit AIRSAL aluminum PIAGGIO VESPINO F9, VELOFAX, GILERA ALX, GSA, TOLEDO, VALE ...
Spare piston for your AIRSAL Ø43.5mm 70cc kit!
Banner
Attention, parts only reserved for competition, prohibited on the road!
Here is the best value for money 70cc aluminum kits on the market. This is the AIRSAL 70cc Ø43,5mm. This inexpensive cylinder does not neglect quality or performance.
43.5mm in diameter, it is made of high-end aluminum and has 6 intake transfers as well as an exhaust with bars.
The diagrams are high enough for the intake and low enough for the exhaust which makes it torquey and not difficult to accompany or adjust. The piston is a two-segment model with side grease nipples!
Clearly, this kit has a very good torque / power ratio, it offers a lot of performance while preserving superb strength!
The piston has a slight preparation on the rear skirt to improve sweeping. The finish is really on top. We recommend that you align the transfers with the crankcases of the lower engine.
The pack contains:
X1 Cylinder
X1 Piston
X2 Segments
X1 Piston pin
X2 Piston clips
X1 Cylinder shim
X2 studs
X1 Notice
As an option we offer a stage 1 preparation, this preparation is a modification of the channels and the exhaust port by increasing the diagrams and improving the duct, it increases the performance of the cylinder. An improvement to the piston and the bottom of the skirt is also included in this modification. Allow a little extra time for this preparation!
Mounts on:
PIAGGIO Vespa al
PIAGGIO Vespa alx
PIAGGIO Vespa nlx
PIAGGIO Vespa Vespino t6
PIAGGIO VESPINO
PIAGGIO VELOFAX
GILERA VALE, TOLEDA, GSA, ALX
And other models ...
Reference: 060609435
Spare piston for your AIRSAL Ø43.5mm 70cc kit!
Reference: 110609435
Replacement segments for your AIRSAL Ø43.5mm 70cc kit!
Reference: 140609435
Ideal in the event of a leak on your cylinder / cylinder head of your PIAGGIO, VESPA!
Reference: 020609435
A high quality and resistant engine! Model without cylinder head.
Reference: 57240.00
Cylinder head without strong and efficient for your moped PIAGGIO CIAO. Available in 10 or 12mm axle choices.
Reference: 3118570
A high solid and powerful engine to improve the performance of your Piaggio moped.
Reference: 15067000
Here is the very efficient Quattrini racing cylinder for Piaggio Ciao. Superior quality, with an exceptional efficiency compared to the different 63cc on the market by a modified cylinder design for bearing to the usual problems of exhaust obstruction on the cylinders of Piaggio Ciao
Reference: 140.0133
A kit very well finished this kit allows a maximum of torque and solidity out of norm.
Reference: 116.0145
An excellent very torquey and robust kit for your old PIAGGIO VESPINO, VELOFAX and your GILERA VALE, TOLEDA, GSA, ALX!
Reference: 140.0065/10ST
The famous POLINI 43mm for piaggio ciao cast iron without cylinder head.
Reference: 140.0136
Finally get rid of the constraints of the CIAO engine, switch to 4 studs and a large diameter exhaust ball joint to release the power!
Reference: 061300
A very clean and well finished cast iron kit that will bring you considerable power gain without denigrating the reliability of your PIAGGIO.
Reference: 3118050 / 3118052
The must of 70cc kit for PIAGGIO Ciao. A real performance monster with 6 intake transfers, large bar exhaust, high compression cylinder head ... An exceptional high engine for guaranteed performance !!!
Reference: 065500
A very clean and efficient kit, in aluminum which will bring you a considerable gain in power without neglecting the reliability of your CIAO. In addition to this, you need to know more about it.
Reference: 48103.00
A high quality and resistant engine! The most powerful kit on the market for VELOFAX PIAGGIO type engine!
Reference: 064900
One of the only aluminum kit that will bring you considerable power gain without denigrating the reliability of your PIAGGIO.
Reference: 5007
Cylinder without solid and powerful ass for your moped PIAGGIO CIAO. Available in 10mm axis only.
Reference: 3118567
The famous MALOSSI CVF available in 10 and 12mm axle with its radial head for CIAO.
Reference: 140.0133/10R
Following many requests, POLINI finally comes out! The version FONTE RACING for ciao !!!