Reference: 06131448
AIRSAL Ø48mm mono-segment piston 12mm axis for 70cc AIRSAL mono-segment kit on minarelli am6
A good quality piston, delivered complete for a refurbishment of your cylinder.
Banner
Here is a kit 70cc first prize of the Spanish house AIRSAL, the model that we call sport mono-segment, this kit also exists in luxury with piston TECH at the price of 138 euros with us! This kit has certainly a low price but yet of a quality and performance well present.
In relation to the two-segment model, it will offer more high speed (this is hardly noticeable) but less longevity and less torque, the piston of the other model is a luxury vertex a bi segment, this one is a lower end so less accurate and solid. Diagrams that are quite low will agree with a small configuration type exhaust + carburetor 21mm.
The finish is not at the top but it remains very correct in relation to the price. The piston is therefore the single-segment chrome hard domed model, it does not have a side grease but a small preparation on the rear skirt to improve the scan and a thin segment of 1mm. The cylinder head is a high compression, the chamber is incoming in order to have a good alignment chamber / cylinder and good resistance of the cylinder head gaskets.
The room is a hemispherical model polished finish. This cylinder head allows you if desired to reconnect the antifreeze on your carburetor. This cylinder is delivered with 2 base seals in order to put the desired squish. Clearly this cylinder is really a superb value for money! It will certainly perform less than a MALOSSI MHR, BIDALOT, or POLINI ... But it will still be very good.
We recommend it with at least : carburation 21mm with prepa air box + slats of valves 0,30mm (original pipe, original valves and diffuser of valves of origin can be preserved), muffler racing, crankshaft and reinforced bearings, cold racing candle ... Attention, this cylinder has an exhaust outlet in Ø28mm and is delivered without shim to 25mm, if you have an exhaust pipe in Ø25mm you will need a shim exhaust.
The pack contains :
Bolt bolts
Pack complete with 2 seals for the squish
Cylinder racing aluminum 5 transfers exhaust with bar
Single-piston piston
domed chrome segment
notice
Cylinder head with high compression inlet chamber
2 piston clips in crab
Piston pin Ø12mm
Optionally we offer a stage 1 preparation, this preparation is a modification of the channels and exhaust light by increasing the diagrams and improving the pipe, it increases the performance of the cylinder. An improvement of the piston and skirt stocking is also included in this modification. Allow a little extra time for this preparation!
Mounts on motorcycles 50cc has gearbox equipped with minarelli am3, am4, am5, am6 euro 1, am6 euro 2 :
APRILIA RS 50cc engine am6 from 1997 to 2006 (attention news after 2006 in derbi euro 3 engine)
APRILIA RX engine am6 (attention news after 2006 in derbi euro 3 engine)
APRILIA MX engine am6 (attention news after 2006 in derbi engine euro 3)
APRILIA TUONO 50cc engine am6 from 1997 to 2006 (attention news after 2006 in derbi engine euro 3)
BETA RR
BETA RR ALU
BETA CRE
HONDA HM
HONDA CRE
HONDA BAJA
HUSQUVARNA WXE
HUSQUVARNA CH
HM DERAPAGE
HM CRE
MALAGUTI DRAKON
MALAGUTI XTM
MALAGUTI XSM
FANTIC CABALLERO
PEUGEOT XP6
PEUGEOT XPS
MOTORHISPANIA RYZ
PEUGEOT XPS
PEUGEOT XP STREET
PEUGEOT XP STREET EVO
PEUGEOT XR6
MOTORHISPANIA RX
PEUGEOT XR7
MOTORHISPANIA RX-R
RIAJU RS1
RIEJU RS2
RIEJU RS2 MATRIX
RIEJU RS2 MATRIX PRO
RIEJU SMX
RIEJU MRX
RIEJU SPIKE
KEEWAY TX EN
YAMAHA DT
MBK X-LIMIT
YAMAHA TZR
MBK X-POWER
SHERCO SM
SHERCO ENDURO
SHERCO HRD
SHERCO ENDURO
And many other machines!
Reference: 06131448
A good quality piston, delivered complete for a refurbishment of your cylinder.
Reference: 11131448 - 11081548 - 11084248
A good quality segment. Ideal in case of loss of compression.
Reference: 04131448
The replacement head for 48mm 70cc on minarelli am6!
Reference: 14131448
Pack spare seals for your kit 70. Ideal for a complete refurbishing of your engine.