Attention prohibited on public roads! This cylinder engine displacement exceeding 50cc is only reserved for the competition on the racetrack, run ...!
Here are the top 80cc engine in the Spanish brand BARIKIT for engine MINARELLI AM6! This model has low price offers good power and a very large increase in engine performance. The cylinder is an aluminum model nikasil treated, so it offers very high reliability and durability. The cylinder has a large exhaust with bar and 4 side intake ports + 1 rear. The base preserves original form, you should still align with housings for the better.
The diameter is 50mm, so it offers a real displacement 76.57cc along with the original 39mm stroke engine MINARELLI AM6. The piston is a mono-segment favoring high revs high silicon content. The piston has a specific skirt, the segment comes with the kit is fine 1 mm, chrome to allow high speeds and ensure high resistance to friction.
The cylinder head is aluminum with plug for antifreeze carburetion, this cylinder head has a high combustion chamber compression hemispherical shape, polished finish. Incoming type of model to align perfectly with the piston and optimize engine power.
Clearly, BARIKIT hits hard with this high engine and puts at disposal its knowledge to performance enthusiasts! And this for a price more than reduced. This cylinder promise you both reliability, power (especially with good diagrams, its 5 transfers its exhaust with bar and its end segment) and many high revs! We will miss only the wedge exhaust (28mm diameter passage to 25mm) is not delivered, however, this is just a detail ... for price and performance developed!
We recommend to accompany this kit with at least: a carburizing Ø21mm (24/25 to make the most well), admission kit with adjustable flexible pipe assembly, exhaust racing, cold candle racing iridium, crankshaft and reinforced bearings , engine oil 100% synthetic racing ....
contains:
Master cylinder Ø50mm aluminum 5 transfers with big exhaust with bar
Aluminum -Culasse incoming high compression hemispherical
-piston Mono-segment Ø50mm
X1 end segment chrome 1mm thick
Axis-piston Ø12mm X 41mm length
Piston Type C -Clips
-pack High engine gasket
-Vissere And connects breech plug antifreeze
Optional we offer a preparation course 1, this preparation is a modification of the channels and the exhaust port by increasing the charts and improvement of the duct, it increases the cylinder performance. Improved piston and bottom skirt is also included in the amendment. Allow a little extra time for this preparation!
This high engine fits the 50cc motorcycles following gearbox fitted the engine MINARELLI AM3, AM4, AM5, AM6 euro 1 am6 euro 2:
-APRILIA RS AM6 engine from 1997 to 2006 (after 2006, attention to motor past DERBI euro 3)
-APRILIA RX engine AM6 (after 2006, attention to motor past DERBI euro 3)
-APRILIA MX engine AM6 (after 2006, attention to motor past DERBI euro 3)
-Beta CRE
RR -Beta
-Beta RR ALU
-Honda HM
-Honda CRE
-Honda BAJA
-HUSQUVARNA WXE
-HUSQUVARNA CH
-HM DERAPAGE
-HM CRE
-MALAGUTI DRAKON
-MALAGUTI XTM
-MALAGUTI XSM
-FANTIC CABALLERO
-PEUGEOT XP6
-PEUGEOT XPS
-PEUGEOT XP STREET
-PEUGEOT XP STREET EVO
-PEUGEOT XR6
-PEUGEOT XR7
-MOTORHISPANIA RYZ
-MOTORHISPANIA RX-R
-MOTORHISPANIA RX
-RIEJU RS1
RS2 -RIEJU
-RIEJU RS2 MATRIX
-RIEJU RS2 MATRIX PRO
SMX -RIEJU
-RIEJU MRX
-RIEJU SPIKE
-KEEWAY TX EN
-YAMAHA DT
-MBK X-LIMIT
-YAMAHA TZR
-MBK X-POWER
SM -SHERCO
-SHERCO ENDURO
-SHERCO HRD
-SHERCO ENDURO
And many other machines!
