
Reference: 272.0001
Clips, rods of axis of piston POLINI in Ø of axis 12mm type crab d.1mm
The pistol type POLINI piston clips for your axis of 12mm, material diameter of 1mm!
Banner
The enthusiasts dreamed it, POLINI did it, the famous POLINI SERIE 6000 kit remade for your old ZUNDAPP engines. This kit is really complete, it has an exhaust pipe internal diameter 29.5mm and external 32.20mm.
An intake pipe with its flexible sleeve internal diameter 19mm, external diameter for rigid carburetor of 24mm, and diameter of the flexible sleeve of 35mm internally for flexible carburetors, if you install a flexible carburetor with this sleeve, you will cut the intake pipe at the entrance, its diameter will then increase to around 25mm.
It is ideal for the installation of a 25mm POLINI, DELLORTO PHBH, PHBL, VHST ... The cylinder is in high quality aluminum with nikasil coating, it has 2 rear transfers which are also used for filling the lower engine which the laterals will then be fed. It is therefore ultimately a real 4 transfers because the 2 rear does not come into action for the PISTON sweep unlike the AM6, DERBI ... The exhaust is a large oval.
The housing inlet skirt diameter is Ø52.9mm, so a 53.1 or 53.2mm reamed housing is required. Between axis of the studs 46X46mm. The piston is a model with high silicon content, with segment in L. The delivered cylinder head has a very worked combustion chamber, hemispherical, micro-blasted finish.
It has a reinforcing bar in the mold to prevent curtains. In view of the quality of aluminum, do not be afraid of cooling, this cylinder will not exceed the temperature required for performance! It will give you a lot of torque and power when you start afresh with your good old ZUNDAPP motorcycle. It is really a superb set that has emerged POLINI, in limited series! Have
Have
Advertised power: 13.6hp at 9800 revolutions per minute
Summary :
For ZUNDAPP engine
Compression ratio: 13.6: 1 (use SP98 mandatory)
For stroke: 41.6mm
Actual displacement: 75.24cc
Skirt diameter Ø52.9mm, perfect crankcase bore 53.1mm
Transfers: 2 rear for low engine filling, 4 side real ones.
Exhaust: Standard oval.
Piston: single-segment, with L-type segment
Cylinder head: high compression microblasted hemispherical chamber
Intake pipe: For 19mm rigid or 25mm flexible (+ if pipe preparation)
Between-axis studs 46X46mm
Exhaust pipe delivered internal Ø29.5mm and external 32.2mm
As an option we offer you a stage 1 preparation, this preparation is a modification of the channels and the exhaust port by increasing the diagrams and improving the duct, it increases the performance of the cylinder. An improvement to the piston and the bottom of the skirt is also included in this modification. Allow a little extra time for this preparation!
Here are some pictures of the preparation:
Reference: 272.0001
The pistol type POLINI piston clips for your axis of 12mm, material diameter of 1mm!
Reference: 271.0006
The replacement piston pin for your large POLINI 12mm axis kit, ideal in case of wear or loss!
Reference: 204.0601/A
Ideal for maintaining your POLINI kit on minarelli P4 or P6 42mm stroke.
Reference: 205.0001
Ideal for a refurbishment of your high engine.
Reference: 216.0101
The POLINI exhaust tube for your old mopeds has gearbox.
Reference: 215.0190
An ideal intake pipe because it can take a lot of carburetors and is changeable!
Reference: 209.0154
Ideal for maintaining your high POLINI S 6000 engine on ZUNDAPP
Reference: 30122.00
Kit very torquey, robust and powerful for GUZZI DINGO 50cc 2T.
Reference: 85445.00
The high complete engine with cylinder head, 70cc, ZUNDAPP for air cooling, small model valves!
Reference: 85207.00
The complete kit 70cc for ZUNDAPP with its cylinder head!
Reference: 85206.00
The piston-cylinder without cylinder head 70cc for ZUNDAPP air cooling as the CS50, KS50 ...
Reference: 133.6005
The kit POLINI SERIE 6000 reproduced for the passionate ones! For 42mm stroke.
Reference: 64432.00
A complete high-performance high-end engine special for SACHS 503 and 504 with a 14mm axle with 2 transfers with a long stroke crankshaft.
Reference: 020306435
Very good little aluminum kit for MORINI M1 engine, M101, M1ES, M1K ... 50 2T!
Reference: 063600
ZUNDAPP is very robust and powerful!
Reference: 85465.00
kit Ø45mm 70cc for ZUNDAP 50 air cooling, admission without valves on cylinder.
Reference: 64445.00
A high-performance and full high special range for motor SACHS 503 and 504 in axis of 12mm with 4 transfers with a short stroke crankshaft.
Reference: 85105.00
Kit offering a great increase in torque and power to your ZUNDAPP 603 engine.
Reference: CI.49.650.G
Very high performance kit for MORINI M1 / M 101 engine!
Reference: 64165.00
A high-performance and full high special range for motor SACHS 503 and 504 in axis of 12 with 4 transfers with a long stroke crankshaft.
Reference: 003800
80cc kit of very high quality, complete with valves and pipe for motorization MORINI era!
Reference: 26105.00
Very torquey, robust and powerful kit for FLANDRIA 50cc 2T.
Reference: 42320.00
A complete high-performance high-end engine special for KREIDLER RS SPORT 50.