
Reference: 009512
ATHENA Racing competition valves minarelli am6
High quality competition valves, bonded aluminum base!
Banner
High quality 80cc ATHENA kit. Ø 48mm big bore, it consists of a high-end nicasil treated aluminum cylinder from EUROCILINDRO.
From an ASSO piston with high silicon content, flat cap with single L-segment.
This excellent set is given with a valve box adhered to the viton with two double slats joined in karbonit fiber, you can mount them with or without slat stops.
Intake plates, muffler ball joint ...
This complete high performance set is obviously very torquey and robust, ideal for refurbishing your old MORINI 2T 50.
As an option we offer you a stage 1 preparation, this preparation is a modification of the channels and the exhaust port by increasing the diagrams and improving the duct, it increases the performance of the cylinder. An improvement to the piston and the bottom of the skirt is also included in this modification. Allow a little extra time for this preparation!
Mounts on old MORINI engines :
Franco Morini 2T G30 - Motorcycles-mopeds
MORINI S5 / GS
KTM SX 50
Malaguti FIFTY FULL CX 50 - 1991/1991 - Motorcycles-mopeds
Moto Gac WINNER 50 - Motorcycles-mopeds
LEM 50
Reference: 009512
High quality competition valves, bonded aluminum base!
Reference: S410000304002
The ATHENA clips of good quality for 12mm axles with 1mm diameter piston groove!
Reference: 001716/R
High-end segment to refurbish and increase your engine compression.
Reference: 021725
The flange has 2 screws for fixing the muffler in Ø29mm ATHENA for P4, P6 ...
Reference: 003803
Pack of complete seal for kit 80cc ATHENA air on MORINI T4, GS, TUNTURI, ZENELLA, PERIPOLI ...
Reference: 26105.00
Very torquey, robust and powerful kit for FLANDRIA 50cc 2T.
Reference: 003100
Very torquey, robust and powerful kit for ZUNDAPP!
Reference: 148.6002
The POLINI 6000 series kit reproduced for enthusiasts! For 44mm stroke. Have
Reference: 64445.00
A high-performance and full high special range for motor SACHS 503 and 504 in axis of 12mm with 4 transfers with a short stroke crankshaft.
Reference: 64262.00
A high-performance high-end special engine for SACHS 503 and 504 in axis of 14mm with 4 transfers crankshaft long race.
Reference: 003800/1
Very high quality 80cc kit, complete with valves and pipe for period MORINI engines!
Reference: 007100
ZUNDAPP is very robust and powerful!
Reference: 020000/1
The ATHENA cylinder, piston, cylinder head, Ø48mm kit for SACHS CORSA LUNGA 50.
Reference: 30122.00
Kit very torquey, robust and powerful for GUZZI DINGO 50cc 2T.
Reference: 54272.00
Piston cylinder for FBM engine, FBM for FABRICA BOLOGNESE MOTOCICLI was the association of MINARELLI and MORINI!
Reference: 53498.00
The very last parmakit for 42mm stroke on MINARELLI P6 engine.
Reference: 85438.00
A 70cc kit for ZUNDAPP air cooling for miniterm engines.
Reference: 020306435
Very good little aluminum kit for MORINI M1 engine, M101, M1ES, M1K ... 50 2T!
Reference: 021700
The cylinder kit, piston, cylinder head, Ø48mm ATHENA for P4R, MACAL, MALAGUTI FIFTY ....
Reference: 64432.00
A complete high-performance high-end engine special for SACHS 503 and 504 with a 14mm axle with 2 transfers with a long stroke crankshaft.
Reference: 074000/1
Very good 70cc kit for SACHS integrated cylinder head! Available with or without intake pipe.