Not approved on the public highway, only reserved for the competition, in any case does not respect the rules of the road!
Here is the ATHENA kit with exhaust valve! This high quality aluminum kit with chrome treatment very upscale nykasil, the finish is excellent. The diagrams are also very good, this kit is wedged between the couple and the high mode, you will reap both, plus it is equipped with an exhaust valve has. Why that ?
This system is often used in cross as it allows for the couple all plans. How does it work ? All simply by a spring system. At low revs there is not so much the gas valve remains down which allows a maximum torque because the exhaust is only 152 ° thanks to its valve.
And the higher up the laps it opens up to 192 °. Therefore clear that allows for a maximum torque without denying high revs. Be careful to adjust the valve is also supplied with a spring game. Also this kit is reputed to do a lot of kilometers for aluminum, surely even the most solid aluminum that is have seen on am6 in 50cc. Its piston is in mono chrome domed end hard segment to allow for higher speeds and avoid friction. The cylinder head is a high polished truncated compression chamber.
The joints are them excellent too, ATHENA is also a leading manufacturer of gasket and recognized worldwide. The exhaust is special form anti-wear / improved scanning.
In conclusion, this is a very solid and powerful aluminum kit able to be used to roll every day (except France because not approved road), doing stunts, etc. Aesthetic level it is relatively sober, it resumes the original shape cleaner, a beautiful metallic gray and is marked ATHENA 3D. Have really appreciate also several seals bases to refine its squish through also for beginners, the manual describes how to squish it and understand it.
We recommend at least: reinforced bearings, reinforced crankshaft, carburation 19mm, exhaust racing, cold candle racing
Features:
Bore (Ø cylinder): 40mm
Displacement: 50cc in race 39mm (origin)
Compression ratio: 10: 1
The pack contains:
-cylinder 5 transfers exhaust normal aluminum treated chromium nykasil d.40mm
-segment end high quality chrome domed d.40mm
-piston mono segment strengthened d.40mm
Axis-reinforced piston (diameter origin)
-clips (axis rushes) C
-pack reinforced complete joint
-cale exhaust (1-2 euro)
yoke -visserie
-culasse high truncated compression polished room d.40mm
-openings of complete exhaust valve
-2 Valve positioning springs
-sticker
-livret ATHENA
Mounting -instruction ATHENA in French / Spanish / Italian / English
Optional we offer a preparation course 1, this preparation is a modification of the channels and the exhaust port by increasing the charts and improvement of the duct, it increases the cylinder performance. Improved piston and bottom skirt is also included in the amendment. Allow a little extra time for this preparation!
Fits the 50cc motorcycles gearbox equipped minarelli am3, am4, am5, am6 euro 1 am6 euro 2:
Aprilia RS 50cc am6 from 1997 to 2006 (new attention after 2006 engine derbi euro 3)
Aprilia RX am6 engine (new attention after 2006 engine derbi euro 3)
Am6 APRILIA MX engine (new attention after 2006 engine derbi euro 3)
Aprilia Tuono 1997 am6 50cc engine 2006 (new attention after 2006 engine derbi euro 3)
BETA RR
BETA RR ALU
BETA CRE
HM HONDA
HONDA CRE
HONDA BAJA
HUSQUVARNA WXE
HUSQUVARNA CH
HM DERAPAGE
HM CRE
MALAGUTI DRAKON
MALAGUTI XTM
MALAGUTI XSM
FANTIC CABALLERO
PEUGEOT XP6
Peugeot XPS
MOTORHISPANIA RYZ
Peugeot XPS
PEUGEOT XP STREET
PEUGEOT XP STREET EVO
Peugeot XR6
MOTORHISPANIA RX
PEUGEOT XR7
MOTORHISPANIA RX-R
RIAJU RS1
RS2 RIEJU
RIEJU RS2 MATRIX
RIEJU RS2 MATRIX PRO
SMX RIEJU
RIEJU MRX
RIEJU SPIKE
KEEWAY TX EN
YAMAHA DT
MBK X-LIMIT
YAMAHA TZR
MBK X-POWER
SHERCO SM
SHERCO ENDURO
SHERCO HRD
SHERCO ENDURO
And many other machines!
