Reference: 53406.02
Bi-piston segment PARMAKIT 40mm (or re-bore) for 50cc kit PARMAKIT CAST and origin on minarelli am6
The PARMAKIT piston replacement for cast iron 50cc on minarelli am6, available in 40mm or 40.25, 40.50, 40,75mm!
Banner
Ideal to start again on new and solid, here is the good 50cc kit PARMAKIT brand, cylinder head with supercharged will install on your minarelli am6. It is the only market in the kit have the additional fixation on the cylinder head for special frame (you do not need to use it).
It is good quality and finish is very good for a relatively low price. It has a piston Bi segment of 1.5mm thick with a hard chrome domed segment. This cylinder permettras you to have a good performance gain compared to the original and above all exceptional reliability. This kit is reputed to be the strongest in the market 50cc. For we surely one of the best iron 50cc kit am6.
It has 7 admission transferyts (6 side and rear), the exhaust is reviewed on the rise in the charts. This upscale kit we can see higher diagrams and a bigger exhaust and cylinder supercharged for a considerable performance boost on your time am6 without neglecting reliability. Delivered 100% complete with its cylinder head, cylinder, engine pack up joint, bi segments piston, rings, clips, pin, exhaust adapter.
Optional we offer a preparation course 1, this preparation is a modification of the channels and the exhaust port by increasing the charts and improvement of the duct, it increases the cylinder performance. Improved piston and bottom skirt is also included in the amendment. Allow a little extra time for this preparation!
Fits the 50cc motorcycles gearbox equipped minarelli am3, am4, am5, am6 euro 1 am6 euro 2:
Aprilia RS 50cc am6 from 1997 to 2006 (new attention after 2006 engine derbi euro 3)
Aprilia RX am6 engine (new attention after 2006 engine derbi euro 3)
Am6 APRILIA MX engine (new attention after 2006 engine derbi euro 3)
Aprilia Tuono 1997 am6 50cc engine 2006 (new attention after 2006 engine derbi euro 3)
BETA RR
BETA RR ALU
BETA CRE
HM HONDA
HONDA CRE
HONDA BAJA
HUSQUVARNA WXE
HUSQUVARNA CH
HM DERAPAGE
HM CRE
MALAGUTI DRAKON
MALAGUTI XTM
MALAGUTI XSM
FANTIC CABALLERO
PEUGEOT XP6
Peugeot XPS
MOTORHISPANIA RYZ
Peugeot XPS
PEUGEOT XP STREET
PEUGEOT XP STREET EVO
Peugeot XR6
MOTORHISPANIA RX
PEUGEOT XR7
MOTORHISPANIA RX-R
RIAJU RS1
RS2 RIEJU
RIEJU RS2 MATRIX
RIEJU RS2 MATRIX PRO
SMX RIEJU
RIEJU MRX
RIEJU SPIKE
KEEWAY TX EN
YAMAHA DT
MBK X-LIMIT
YAMAHA TZR
MBK X-POWER
SHERCO SM
SHERCO ENDURO
SHERCO HRD
SHERCO ENDURO
And many other machines!
Reference: 53406.02
The PARMAKIT piston replacement for cast iron 50cc on minarelli am6, available in 40mm or 40.25, 40.50, 40,75mm!
Reference: 53406.16
Set of two segments PARMAKIT for kits 50cc cast iron on minarelli am6!
Reference: 53401.03
The spare seal pack for the 50cc cast iron PARMAKIT on minarelli am6!
Reference: IM1
New range of MVT cylinders for your MINARELLI AM6 engine!
Reference: EQ-716
High complete engine ideal for respecting the 50cc displacement and circulating every day. 7 transfers, enlarged oval exhaust, high compression cylinder head mounted on O-ring, bi-segment piston... .
Reference: EQ-922-S
High complete engine ideal for respecting the 50cc displacement and circulating every day with an efficient kit 5 transfers, bar exhaust, high compression cylinder head with incoming stud, mono segment piston ...
Reference: EQ-991-S
High complete engine ideal for respecting the 50cc displacement and circulating every day with a high-performance kit. 5 transfers, bar exhaust, high compression cylinder head with incoming stud, single segment piston ...
Reference: 133.1011
A very good high engine which brings a very good performance gain while preserving the solidity and the legal displacement of 50cc.
Reference: CK.44.492.G2
A very powerful kit with a specific admission has 6 lateral transfers and a stud bolt! Performance level! To put with the POLINI and MALOSSI!
Reference: 220399
Here is a high quality good motor much cheaper than the origin which offers better heat dissipation, less friction ...
Reference: 504636
The latest from DOPPLER, the high cast iron engine which brings a very good performance gain while preserving the solidity and the legal displacement of 50cc.
Reference: 013006476
The deluxe version of 50cc AIRSAL bi-segment, a powerful kit, strong, torquey and especially with an attractive price, very good engine preparation base.
Reference: 011332403
The luxury version of the AIRSAL 50cc in two-segment, a powerful, solid, torquey kit and above all with an attractive price, very good basis for engine preparation.
Reference: 032065
Here is a top engine of very good quality much cheaper than the origin which offers better heat dissipation, less friction...
Reference: KT00098
A high, solid and efficient 50cc engine. High quality and approved for daily circulation.
Reference: 11000042
A powerful kit to install with a crankcase alignment and a good configuration low engine, exhaust and carburetion!
Reference: 032062
For a complete refurbishment of your high-end CPI engine at a low price.
Reference: 3112199
A 50cc kit very powerful and solid, ideal for driving every day with reinforced crankshaft, 21mm carburetion, racing exhaust ...
Reference: 478325
Ideal for refurbishing your high CPI engine.