- -40%
Reference: 213.0012
POLINI competition valves for scooter VESPA ET3, ETS, SPECIAL ... PIAGGIO APE 50, 125cc
High-end valves complete with slats. To be assembled in the pipes admission kits with POLINI valves from VESPA, APE ...
Banner
With many studies and designed in the best materials, here is the mono-slat system on the Ø19mm 3-hole POLINI intake manifold for VESPA scooter.
Obviously of high quality, it eliminates all the drawbacks of the original intake.Gain torque, power, speed and consumption by switching to a carbon valve system! It can be fitted with original crankcases and crankshaft with 16 to 24mm carburetion.
For more power, POLINI recommends preparing the casings. Delivered complete as presented To accompany the original 19mm carburetor or ideally a POLINI 21 carburetor reference 201.2103 or 19 reference 201.1905 .
As a download link, a 100% complete PDF of the technical diagram and advice on how to use this admission.
POLINI strongly advises after 200 km of use to carry out a serious and general check of the installation of this admission. To check tightness and locking against the crankcase. All this due to the increase in power caused by this competition piece.
Mounts on:
VESPA 50 HP
VESPA 50 FL2
VESPA 50 PK
VESPA 50 XL
VESPA 125 ETS
VESPA 125 PK
VESPA 125 XL ...
Reference: 213.0012
High-end valves complete with slats. To be assembled in the pipes admission kits with POLINI valves from VESPA, APE ...
Reference: 201.1905
A carburetor pre-set and delivered ready to be mounted on your original vespa 50 and 125 pipe.
Reference: 201.2103
A pre-adjusted carburetor delivered ready to be fitted to your original vespa 50 and 125 pipe.
Reference: 5304
Intake pipe for your SHBC 19.19 carburettor.
Reference: 215.0232
Ideal to pass on a system has flaps and thus to gain in couple, power and consomation! To accompany a 17,5mm POLINI CP special for the best!
Reference: 215.0203
Unique and powerful design, POLINI monolamelle system for VESPA carburizing scooter in 19 or 21mm diameter with 2 fixing holes. For carburettors origin or CP POLINI!
Reference: 20 5461
The best way to mount a large PHBL carburetor on your VESPA ETS and PK 50 or 125cc and increase your performance!
Reference: 215.0116
Inlet kit with single-flap valves! Gain of torque and very high power in relation to a mounting without valves. For carburetor of origin or CP 19 and 21mm rigid special or flexible standard.
Reference: 215.0005
Black painted steel pipe for 16/16 carburettors on VESPA 50 SPECIAL 2T.
Reference: 20 4709
Inlet pipe for MALOSSI carburettors or other soft mountings on your VESPA scooter.
Reference: 215.0118
Valve system with flexible sleeve for increased power and torque!
Reference: 15801000
Replacement intake manifold for your VESPA!
Reference: 215.0163
For an improved admission with carburettor POLINI CP 24mm flexible mounting, fixing by 3 holes!
Reference: 11251700
Replacement aluminum intake sleeve for your VESPA!
Reference: 215.0270
Valve inlet kit for increased performance, pipe fitting Ø 23mm.
Reference: 215.0233
For an improved admission with carburettor POLINI CP 24mm, fixing by 3 holes! High performances guaranteed!
Reference: 215.0117
Ideal to pass on a system has flaps and thus to gain in couple, power and consomation! To accompany a 17,5mm POLINI CP special for the best!
Reference: 215.0112
Valve inlet pipe for special kit POLINI 140.0051 / L.
Reference: 02 5084B
Ideal for improving and optimizing the performance of your PIAGGIO APE scooter.