- -8%
Reference: 27 2728.C0
Set of 3 pre-cut MALOSSI carbon valve slats Peugeot fox, scooters & Honda wallaroo
Out of the ordinary finish. Here are valves that will bring you reliability, longevity and power.
Banner
Room not approved on road, only reserved with the competition.
This 70cc MALOSSI provides a model without cylinder head, it is intended to be mounted with original cylinder head PEUGEOT Air scooter before 2007 which makes it cheaper and still good enough. The cylinder is a cast iron model reamed in Ø47mm diameter to increase the engine, lights / transfers have a very good finish making it very reliable and solid, the piston is a two segment to slow the race, privilege the couple and solidity.
It is an axis of 12mm model and it will bear an original crankshaft without problems. The cylinder head gasket is a model unlike aluminum complete kit with cylinder head that is cylinder head O-ring. This little kit is really cheap and will bring you decent performance in torque and top speed without requiring a large equipment behind a single exhaust, carburetor settings with candle index 9 (B9HS) will be sufficient to properly operate this little kit.
MALOSSI book with this kit, a valve slide in KARBONIT to exploit the good diets and carburetion follow without problems. We suggest this room are those who are in a country where the law permits to circulate every day on road 70cc kit, ideal in case of tightening your high engine of origin and obtain a gain of felt performance, engine performance improved!
We advise to accompany this kit with: carburation 17,5mm, cold candle racing, racing exhaust, a setting of your drive ....
The pack contains:
X1 Piston
X2 Segments
X1 Axis 12mm
Pack complete joint X1
X2 piston Clips C
X1 cast iron cylinder
X1 lamella valves
X1 Instructions
X3 Stickers
Optional we offer a preparation course 1, this preparation is a modification of the channels and the exhaust port by increasing the charts and improvement of the duct, it increases the cylinder performance. Improved piston and bottom skirt is also included in the amendment. Allow a little extra time for this preparation!
Mounts on motor scooter Peugeot 50cc 2-stroke vertical air:
-BUXY
-ELYSEO
-SPEEDAKE
-SEEDFIGHT 2 AC
AC -SPEEDFIGHT
-SQUAB
-TREKKER
-TKR
-VIVACITY
-ZENITH
And other models ...
Reference: 27 2728.C0
Out of the ordinary finish. Here are valves that will bring you reliability, longevity and power.
Reference: 36 4450
Do not forget to change at each winding to prevent engine failure thereafter.
Reference: 19 3298E
Set of 2 M6 studs which can be used for many applications.
Reference: 2311783B
Piston pin with shaped clips "C", essential for refurbishment quality and reliable.
Reference: 35 4501
Ideal in case of starting tightening, heating ... for refurbishment!
Reference: 34 7036
The spare piston diameter 47mm for 70cc MALOSSI cast iron kits on scooters like HONDA, PIAGGIO, PEUGEOT, MINARELLI VERTICAL and HORIZONZAL ...
Reference: 11 7206
A quality seal pack, ideal for winding without leaking!
Reference: 142.0147/R
A very well studied kit, touch up by hand to have as much performance as aluminum kits while enhancing the solidity of a cast iron kit.
Reference: 31 8640
A kit certainly a little less powerful than a team but which can surprise more than one.
Reference: CI.26.651.G
The only aluminum kit and the most powerful kit available for this engine architecture!
Reference: 02041946
Powerful and strong, this 70cc is an excellent quality / price / power!
Reference: 142.0147
A high engine with a quality / price / performance ratio excellent! For us, one of the best in the market in 70cc Peugeot scooter.
Reference: 02042848
Cylinder piston with segments for scooter HONDDA VISION 80cc.
Reference: 070600
A very powerful kit, even more powerful than the MALOSSI MHR REPLICA 70!
Reference: KT00058
A high engine without strong and powerful 70cc cylinder head, ideal for increasing your performance.
Reference: 9908660
A 100% complete, efficient and reliable 70cc cast iron kit for scooter PEUGEOT Vivacity, Trekker, Speedfight, ....
Reference: 02022046
Ideal in case of breakage, heating or motor clamp to a less expensive change.
Reference: 010224476
Escapement barrete, piston mono-segment, 47.6mm in diameter! A good little monster power!
Reference: CIL-705
Ideal together to improve performance, all at a lower cost!
Reference: 010241476
This kit will offer more torque while keeping good reliability at a reasonable price.
Reference: 01022046
5 transfers exhaust with oval, bi-segment piston and cylinder head high compression 46mm in diameter, a good kit torquey and very strong!
Reference: 30425.M
A cylinder head without strong and torquey 70cc, ideal to optimize your performance. Equipped with 5 transfers, aluminum material with large exhaust and VERTEX piston mono segment.
Reference: CIL-730
A good kit without cylinder head, ideal to refurbish your engine with more performance!