Banner
This kit will offer more torque while keeping good reliability at a reasonable price.
Attention room only reserved for the competition, prohibited on road!
Here the kit 70cc T6 AIRSAL in full 47,6mm diameter. This kit will give you very good performance in low revs thanks to its dual piston segments. 
Featuring an admission to 6 transfers, the cylinder has been reviewed and revised upwards with slightly modified diagrams, it has an exhaust barrette and well crafted channels. This model is aluminum of good quality, the finish is also good. 
The cylinder head is a high compression polished finish aluminum model. Clearly, this cylinder will allow you to start again on new equipment in all compliance, while combining reliability / quality / performance / price! 
We recommend to accompany this kit with: carburation 19mm (carbon flaps slats 0.30mm or 0.35mm), crankshaft and reinforced bearings, exhaust racing, cold candle B10 ... 
The pack contains:
X2 clips of piston in G
X2 end chrome segment
X1 piston Ø47,6mm
X1 axis Ø12 piston
X1 cylinder head high compression
X1 aluminum cylinder 6 transfers, exhaust barrette
X1 pack reinforced engine joints high
-X2 Exhaust studs
-Notices ... 
Optional we offer a preparation course 1, this preparation is a modification of the channels and the exhaust port by increasing the charts and improvement of the duct, it increases the cylinder performance. Improved piston and bottom skirt is also included in the amendment. Allow a little extra time preparing for this view on the preparation!: 
Mounts on motor scooter Peugeot 50cc 2-stroke vertical air:
-BUXY
-ELYSEO
-SPEEDAKE
-SEEDFIGHT 2 AC
AC -SPEEDFIGHT
-SQUAB
-TREKKER
-TKR
-VIVACITY
-ZENITH
And other models ...
Reference: 040241476
The cylinder head replacement for your 70cc T6 AIRSAL Ø47,6mm on scooter Peugeot air before 2007!
Reference: 060241476
The replacement piston diameter 47,6mm for kits 70cc T6 AIRSAL!
Reference: 110241476
2 high range segments chrome and already pre-rehearsed.
Reference: 140241476
A pack seal of quality to change each motor winding for perfect tightness.
Reference: 31 7132
A kit to mount the cylinder head of origin, performance and durability with low price!
Reference: 070600
A very powerful kit, even more powerful than the MALOSSI MHR REPLICA 70!
Reference: KT00058
A high engine without strong and powerful 70cc cylinder head, ideal for increasing your performance.
Reference: 142.0147/R
A very well studied kit, touch up by hand to have as much performance as aluminum kits while enhancing the solidity of a cast iron kit.
Reference: 010224476
Escapement barrete, piston mono-segment, 47.6mm in diameter! A good little monster power!
Reference: 31 7133
A solid, reliable and high torque engine!
Reference: 01022046
5 transfers exhaust with oval, bi-segment piston and cylinder head high compression 46mm in diameter, a good kit torquey and very strong!
Reference: 02042848
Cylinder piston with segments for scooter HONDDA VISION 80cc.
Reference: 02041946
Powerful and strong, this 70cc is an excellent quality / price / power!
Reference: 30425.M
A cylinder head without strong and torquey 70cc, ideal to optimize your performance. Equipped with 5 transfers, aluminum material with large exhaust and VERTEX piston mono segment.
Reference: 010241476
This kit will offer more torque while keeping good reliability at a reasonable price.
Reference: 142.0147
A high engine with a quality / price / performance ratio excellent! For us, one of the best in the market in 70cc Peugeot scooter.
Reference: 020224476
Ideal in case of breakage, heating or motor clamp to a less expensive change. If you already have a cylinder head 47,6mm.
Reference: 02022046
Ideal in case of breakage, heating or motor clamp to a less expensive change.
Reference: 9908660
A 100% complete, efficient and reliable 70cc cast iron kit for scooter PEUGEOT Vivacity, Trekker, Speedfight, ....
Reference: CIL-705
Ideal together to improve performance, all at a lower cost!
