- -8%
Reference: 34 7849
Piston bi segment Ø47mm axis 12mm for kit MHR and MHR Replica 70cc vertical minarelli, minarelli am6 ...
Ideal in the event of compression losses, to be changed every 8,000 km!
Banner
Not approved on public roads, reserved only for competition, does not respect the regulatory displacement in any way!
In the category of thermal groups "Sport aluminum", we present you this kit MALOSSI MHR REPLICA diameter Ø47mm. This cylinder is the replica of the famous MALOSSI MHR TEAM! This model is certainly slightly less powerful than its counterpart MHR TEAM but it remains nevertheless torquey and solid!
The MALOSSI MHR TEAM stud bolt has been replaced by a normal "monobloc" cylinder head, the combustion chamber is a frustoconical model with polished finish, high compression The cylinder is like the MALOSSI MHR TEAM, a diameter of 47mm.
There are 6 transfers and they are relatively well worked (front angle under the exhaust for better sweeping and more performance). The transfer channels are very studied, they do not require any preparation.The exhaust is a model with boosters in order to preserve a good solidity while opening up the exhaust to the maximum.
In order to slow down the race for more solidity, MALOSSI put a bi segment piston, these segments are high-end hard chrome domed models 1.5mm thick in order to slightly slow the high speeds for the benefit of torque and solidity . The piston is a very high-end model like all MHR pistons, it has side grease nipples as well as a preparation on the skirt to improve the sweeping and filling of the intake, has a very high content in silicon for improved heat exchange surfaces.
To finish the presentation of this magnificent high engine, this kit is an extremely powerful model but above all very solid thanks to the specific treatment employed, the alloys and the MALOSSI MHR bore which are of the most upscale on the competition cylinder market! Whether for endurance, the stunt ... this kit will not disappoint you and will offer you guaranteed sensations! Delivered complete as presented. We recommend accompanying this kit with at least: racing exhaust, 21mm carburetion, unbridled competition ignition, reinforced crankshaft, reinforced bearings, hard clutch springs, NGK competition or Iridium spark plug, 100% synthetic racing engine oil, etc. .
The pack contains:
-Cylinder MALOSSI MHR REPLICA Ø47mm 6 transfers with exhaust boosters
-High compression aluminum cylinder head Ø57mm monobloc, tapered with polished finish
-Piston bi-segments Ø47mm with side grease nipples and preparation on the rear skirt
-X2 segment Ø47mm X 1,5mm
-Reinforced piston axis Ø12mm X 38mm in length
-C piston clips Ø12mm X 1mm thick
-X2 reinforced exhaust studs M6 X length 270mm
-Pack full seal
-Notice-Stickers
Installs on Peugeot Vertical Liquid 50cc 2-stroke engine scooter:
PEUGEOT SPEEDFIGHT 2 50 2T LC 2004->
PEUGEOT SPEEDFIGHT 50 2T LC
PEUGEOT X-FIGHT 2 50 2T LC 2004->
PEUGEOT X-FIGHT 50 2T LC
And many other models ...
As an option we offer you a stage 1 preparation, this preparation is a modification of the channels and the exhaust port by increasing the diagrams and improving the duct, it increases the performance of the cylinder. An improvement to the piston and the bottom of the skirt is also included in this modification. Allow a little extra time for this preparation!
Reference: 34 7849
Ideal in the event of compression losses, to be changed every 8,000 km!
Reference: 35 7259
Ideal in case of loss of compression and to put your high engine to nine.
Reference: 27 2728.C0
Out of the ordinary finish. Here are valves that will bring you reliability, longevity and power.
Reference: 36 4450
Do not forget to change at each winding to prevent engine failure thereafter.
Reference: 2311783B
Piston pin with shaped clips "C", essential for refurbishment quality and reliable.
Reference: 38 9894
MALOSSI cylinder head replacement, high compression for kit 70cc MALOSSI MHR REPLICA for engine scooter PEUGEOT Vertical Liquid!
Reference: 15 9910
Liquid cooling flange connection type for your kits MALOSSI PEUGEOT, Derbi, Aprilia ....
Reference: 06 8826
MALOSSI cylinder head surround O-ring.
Reference: 11 9842
Essential for refurbishment perfect and without leakage. Make sure you change your joints at each disassembly / reassembly.
Reference: 31 9476
MHR REPLICA kit on liquid Peugeot scooter, standard race and original size transfers of course ... But what power! What a couple and what solidity !! One of the best normal races on the market!
Reference: P400420100004
Reference: 010231476
A good ratio between high revs, power, price and durability. Sport model with piston mono segment.
Reference: 31 9476
MHR REPLICA kit on liquid Peugeot scooter, standard race and original size transfers of course ... But what power! What a couple and what solidity !! One of the best normal races on the market!
Reference: KT00116
A high complete 70cc solid and efficient engine, ideal for increasing your performance.
Reference: 010243476
A very good price / quality, performance and torque! VERTEX luxury model with dual piston segments.