Reference: 6611785B
Needle cage reinforced MALOSSI Ø12X17X16mm minarelli am6, DERBI, PIAGGIO, scooters ...
High quality needle cage, reinforced! ideal on the most advanced configurations.
Banner
Unapproved, banned on public roads for competition and closed circuits!
The cylinder / piston without cylinder head 70cc MALOSSI MHR TEAM is a concentrated authentic performance with its design, study, architecture and elements that accompanies it. Its aluminum cylinder nikasil treated with specific heat treatment, has excellent finishes and has 7 large intake transfers extensively revised upwards with a massive exhaust with bar.
The piston is a model mono segment Ø47,6mm diameter promoting high speeds (reducing friction), equipped with its end segment chrome domed honed, clips reinforced C and its axis 12mm. Also (piston) was created from the finest materials to ensure good heat resistance and temperature changes with an outer coating of graphite to an even lower coefficient of friction.
. Delivered 100% as shown Machining housings will be essential for the passage of a cylinder with only MALOSSI crankshaft (refs 53 8009 - 5,314,548 to 5,312,810). With gasket set for the squish, studs, accessories, hardware ....
We recommend to accompany this high engine with at least: minimum Ø21mm carburizing, an intake kit, racing exhaust, ultra reinforced vilbebrequin (brand MALOSSI required to mount it), reinforced bearings, cold candle racing, oil 100% synthetic motor racing, a large variation range, a racing ignition, careful monitoring and running, mounting in the rules ....
Optional we offer a preparation course 1, this preparation is a modification of the exhaust port by increasing the charts and improvement of the duct, it increases the cylinder performance. Improved bottom skirt is also included in the amendment. Allow a little extra time for this preparation!
Itself on:
Engine 2 Time minarelli horizontal liquid scooter.
2 motor scooter minarelli horizontal air Time Spent liquid (long only).
APRILIA AREA 51 LC
APRILIA GULLIVER 50
Aprilia SR 50 LC NETSCAPER
APRILIA RALLY 50 LC
RACING APRILIA SR 50 LC
APRILIA SONIC LC
APRILIA SR REPLICA LC
APRILIA SR STEALTH
BENELLI 491 SPORT LC
BENELLI K2 50 LC
BETA ARK 50 LC
BETA EIKON 50 LC
GSP GARELLI 50 LC
ITALJET DREAGSTER 50 LC
MALAGUTI F15 FIREFOX 50 LC
MALAGUTI F12 DIGIT KAT LC
MALAGUTI F12 LC Phatom
MALAGUTI F12 R LC
MBK MACH G 50 LC
MBK NITRO 50 LC
YAMAHA AEROX 50 LC
YAMAHA JogRR 50 LC
Reference: 6611785B
High quality needle cage, reinforced! ideal on the most advanced configurations.
Reference: 36 4450
Do not forget to change at each winding to prevent engine failure thereafter.
Reference: 38 9513
For stud head only, covers aluminum cylinder head essential to replace your old piece out of use.
Reference: 1113209B
A seal pack upscale, essential for a safe winding and leakage.
Reference: 19 9419Q
Ideal for replacing your old bolts MALOSSI MHR.
Reference: 34 8654.A0
A spare piston high-end treatment with graphite, several sizes available!
Reference: 27 8359B
Essential for the refurbishment of your cooling system.
Reference: 3513982B
Ideal for refurbishing your high engine.
Reference: 2312580
Reinforced MALOSSI piston pin, ideal for the loss of the old piston pin!
Reference: 38 9512
A replacement stud with a high compression chamber of very good quality.
Reference: 32.133/M3
The only repair your cylinder for maximum kit 80cc Ø47,6 SIMONINI kit minarelli horizontal liquid scooter engine.
Reference: 31 8429
A high performance engine without cylinder head, powerful, reliable and sturdy scooter minarelli horizontal liquid and yamaha.
Reference: 32.131/M3
The single cylinder 70cc to repair your Ø47,6mm SIMONINI kit minarelli horizontal liquid scooter engine.