PEUGEOT 103
MBK 51
MOTOBECANE
PIAGGIO CIAO / VELOFAX
PEUGEOT FOX
HONDA CAMINO, PX, PXR...
DERBI VARIANT.png)
SOLEX
PUCH
MINARELLI AM6
Low-pass exhaust pipe
High-pass exhaust pipe
DERBI Euro 3 / 4 / 5
DERBI Euro 1 & 2
MINARELLI P4 & P6.png)
MINARELLI RV6, RV5, RV4, RV3
SUZUKI SMX, RMX, TSX
YAMAHA TY, RD, DT, MX
HONDA MB, MT, MTX, MBX, NSR R
YAMAHA CHAPPYBanner
Vilo 2FAST long race for your am6 engine, a focus of performance!
Not approved on open road, part formally reserved for competition, this crankshaft increases the engine cylinder capacity.
A very worked competition crankshaft, very expensive but very high-end piece! Race increased to 47mm, elongated wire 95mm obviously mechanized ultra reinforced! Dynamic balance very advanced and specific to the 100cc kit from 2FAST! 14mm piston axis specific to the kit 2FAST 100cc!
Masses increased in diameter, must be placed on the 100cc crankcases from TPR or in original crankcases with milling / machining!
*With a 2mm milling at the foot, allows to place the TPR 100 AM6 kits
*By milling the foot of the cylinder by 5mm (or crankcase side), it allows the cylinder to operate MALOSSI MHR 100!
14x17x16,5mm (lays 13mm and 12mm axes possible with other cages in outside Ø 17mm
Gets on 50cc motorcycles with gearbox equipped with the engine minarelli am3, am4, am5, am6 euro 1, am6 euro 2:
APRILIA RS 50cc am6 engine from 1997 to 2006 (new attention after 2006 in euro derbi engine 3)
APRILIA RX am6 engine (new attention after 2006 in euro derbi engine 3)
APRILIA MX Am6 engine (new attention after 2006 in euro derbi engine 3)
APRILIA TUONO 50cc am6 engine from 1997 to 2006 (new attention after 2006 in euro derbi engine 3)
BETA RR
BETA RR ALU
BETA CRE
HONDA HM
HONDA CREE
HONDA BAJA
HUSQUVARNA WXE
HUSQUVARNA CH
HM DERAPAGE
HM CRE
MALAGUTI DRAKON
MALAGUTI XTM
MALAGUTI XSM
FANTIC CABALLERO
PEUGEOT XP6
PEUGEOT XPS
MOTORHISPANIA RYZ
PEUGEOT XPS
PEUGEOT XP STREET
PEUGEOT XP STREET EVO
PEUGEOT XR6
MOTORHISPANIA RX
PEUGEOT XR7
MOTORHISPANIA RX-R
RIEJU RS1
RIEJU RS2
RIEJU RS2 MATRIX
RIEJU RS2 MATRIX PRO
RIEJU SMX
RIEJU MRX
RIEJU SPIKE
KEEWAY TX EN
YAMAHA DT
MBK X-LIMIT
YAMAHA TZR
MBK X-POWER
SHERCO SM
SHERCO ENDURO
SHERCO HRD
SHERCO ENDURO
ICC SM
And many other machines!
Reference: 12100880
Competition crankshaft to reinforce the prepared engine of your DERBI euro 3 and 4.
Reference: 23180.14
A crankshaft designed for the famous 110cc kit from PARMAKIT. But easily mounts on other engine. Be careful, however, not to have too high diagrams.
Reference: 31087550
Linkage of quality and at a good price! 45mm long stroke model. In addition to this, you need to know more about it.
Reference: CB.12.95
Special crankshaft 42.00mm long stroke, 90mm forged connecting rod, ... with silver treated needle cage. Ideal for increasing its displacement and strengthening its low engine as it should.
Reference: 12100982
A high-end crank assembly, special 48.00mm long stroke to accompany a BIDALOT FACTORY 94cc high engine with machining of the engine casings!
Reference: CB.12.245.214
Special fitting long stroke 44.90mm high-end Mazzuchelli, forged rod machined in mass 90mm, ... with silver treated needle cage Ø 14mm. Dynamic balance designed to be assembled without balancer.
Reference: 9930210
Special high-end 44mm long stroke connecting rod, 90mm machined forged connecting rod, ... With Ø12 mm silver treated needle cage Dynamic balancing designed to be assembled with a balancer.
Reference: CB.12.243.1
Special high-end 43mm long stroke connecting rod, 90mm machined forged connecting rod, ... With Ø12 mm silver treated needle cage Dynamic balancing designed to be assembled with a balancer.
Reference: TFAST053
Vilo 2FAST long race for your am6 engine, a focus of performance!
Reference: 5318895
Special fitting run long 47mm and 100mm rod for MHR 100cc sets on DERBI EURO 3, 4 and 5
Reference: CIG-141R
Well reinforced with better balance and more strength than the normal BARIKIT model. This 45mm stroke is ideal for increasing your stroke, displacement, power, torque ....
Reference: CIG-85R
Well reinforced with better balance and more strength than the normal BARIKIT model. This 43mm stroke is ideal for increasing your stroke, displacement, power, torque .... With a 1.5mm shim.
Reference: CB.12.245.2
Mazzuchelli top-of-the-range 44.90mm special long stroke crankshaft, forged connecting rod machined in the mass 90mm, ... with Ø12 mm silver treated needle cage Dynamic balancing designed to be assembled without balancer.
Reference: CB.12.243.2
Special high-end 43mm long stroke connecting rod, 90mm machined forged connecting rod, ... with Ø12 mm silver treated needle cage Dynamic balancing designed to be assembled without balancer.
Reference: VI32
Special long run 44.8mm high-end, forged and polished steel rod 90mm, ... With needle cage Ø12 or 13mm. Balance made to decrease vibrations.
Reference: CIG-132R
A high quality crankshaft, ideal for strengthening your low engine with a stroke very slightly increased by 40.7mm.
