Reference: KT00073
§ Kit 70cc Ø46mm DR racing cast air Peugeot 103, fox & wallaroo
Super strong and torquey, the only 70cc kit with the ATHENA which is very well suited to crankcases with 2 transfers!
Banner
Attention, not approved on road, only reserved with the competition.
Here is the AIRSAL T3 kit with admission W. This model is for Peugeot Fox and Honda Wallaroo mounted air cooling. Perform much better than 50cc and yet so inexpensive kit ... It was planned to have the performance, torque and especially preserving a maximum solidity with a simple installation! Clearly this kit does not require large equipment to function properly!
A relaxing escape, a reinforced crankshaft with a small 17mm carburetor in ample enough has run this cylinder. Admission W will allow a formal quality improvement report by scanning a single rear transfer, it will also allow to have a wide inlet with a small back transfer, the system also works great on the casings 2 transfers PEUGEOT first generation. Lateral transfers are two in number, you will by a touch up your casings to align this kit, it works very well on original casings.
The piston is a model Bi segment with a bulging chrome for the top. Bi segment will slow down the race and offer more torque / strength in spite of the high speed. The piston has undergone a peening on the cap, this type of act is done to avoid detonation. The diagrams are quite high in relation to many 70cc market, oval exhaust is a normal model. In short, this high engine will be a good companion for the roads of the country which authorizes because it is very strong, torquey and his recovery is good! The increase in power next to a source will be very well felt. A superb quality / price / performance. Non contractual picture Warning saggy and the rollers are no longer comes with!
We recommend to accompany this kit with at least: exhaust of relaxation, reinforced crankshaft bearing clearance C3, carburation in 17mm PHBG 19 PHBG + pipe + 0.30mm blade of carbon valves, index 9 at NGK spark plug, cylinder head d.46mm (the POLINI fontione fine).
The pack contains:
X2 segments Ø46mm X 1,5mm
X1 dual piston segment
X1 piston pin
X2 crab piston clips
X1 gasket
X1 admission T3 cylinder 70cc air W
!!! think to buy a cylinder base gasket !!!
Optional we offer a preparation course 1, this preparation is a modification of the exhaust port by increasing the charts and improvement of the duct, it increases the cylinder performance. Improved bottom skirt is also included in the amendment. Allow a little extra time for this preparation!
Reference: KT00073
Super strong and torquey, the only 70cc kit with the ATHENA which is very well suited to crankcases with 2 transfers!
Reference: 31 8393
high-end kit well worked with excellent finishes.
Reference: 142.0100
W exhaust, liquid cooling, 6 intake transfers, mono-segment, chrome treated aluminum... What more could you ask for from a 103!
Reference: CI.26.650.G
Overpowered kit on the verge of extinction. Out of production!
Reference: 142.0086
Ideal for a coupled jam! Majorized transfers, strength, simplicity, guaranteed performance POLINI!
Reference: CIL-941-S
A powerful and solid kit, ideal for improving your performance!
Reference: 31600.00
An excellent Made In Italy kit, performing, solid, high quality guaranteed!
Reference: 31 8384
The well-known MALOSSI cast iron 70cc. Solid, torquey, not neglecting power, it is an ideal companion for long endurance trips where performance is required.
Reference: 119.0052
A kit full of power and quality while keeping high-end manufacturing products.
Reference: HM42
The monstrous S RACE 70cc for PEUGEOT 103 is finally there!!!!
Reference: 119.0055
Kit with a lot of torque and recovery at high speed.
Reference: 002300
Super solid with its aluminum and its very high quality processing, its architecture also allows very good performance.
Reference: 31 8388
Very good kit level performance, torque and quality always at the rendezvous.
Reference: 02022546
A kit at a low price and yet very efficient in addition to being a very good basis for preparation with its exhaust has boosters, its 6 transfers and its mono-segment (or bi-segment).
Reference: 56207.00
A very good rare and powerful kit to be accompanied by a good high compression cylinder head in Ø46mm.
Reference: 56257.00
A superb cylinder, rare and well structured! A great base for those who don't like to be like everyone else.