
Reference: 204.0201/A
Piston POLINI luxury Ø46mm mono-segment for 70cc aluminum kit Peugeot 103 / fox / wallaroo
The luxury piston with replacement chrome segment for 70cc aluminum kits from Peugeot 103.
Banner
Attention, not approved and prohibited on the road, reserved only for competition.
Here is an Asian version of the 70cc liquid kit W 6 transfers for PEUGEOT 103. Clearly more affordable than an Italian brand version, however, it is not worth the quality of Italian! Quality control, aluminum ingots, nicasil, pairing... Everything is obviously discounted to see a more affordable price be offered! There remains, for a reduced price, a nice base of engine preparation! It takes over the advantages of the Italian kit, namely:
-6 transfers of admission
-Escapement in W
-Piston mono-segment
-Aluminium with nicasil coating
-High compression cup with hemispheric chamber
....
It is therefore a cylinder kit to be accompanied by a good sports exhaust, a large carburation, crankcases racing or at least, original crankcases aligned to the base of the cylinder... From the base, this cylinder has low diagrams and targets rather low speeds (around 7,500 to 8,500 rpm), obviously, a preparer can take it further. But in the latter case, it is strongly recommended to take a high quality Italian version with a nice pairing! A beautiful honing, piston and high-end coating...
*Warning, delivered without base joint and without central cap joints! Plan a joint game POLINI if you want to have the complete kit ready to pose!
diagrams (may vary according to series) and techniques:
lateral transfers (number 4): 113°
rear transfers (number 2): 104°
centre exhaust (W): 161°
exhaust (W) sided: 157°
room volume: 6,35ml
compression ratio 11.23: 1
treatment: chrome
actual cylinder capacity: 64,98cc on Peugeot original race 39,1mm
fine segment e: 1.00mm
high silicon mono-segment piston ASSO
Advice for small preparation: in order to operate more high speed without losing too much torque, you will be able to pass on diagrams: ech 187° / lat 129° / ar 126° with a rate at 14,5 : 1, this type of diagrams will greatly increase the engine power without harming its good behavior. Accompany this type of preparation with cap polishing, exhaust polishing and combustion chamber polishing.
The skirt is also to be reworked as well as the base!
the pack contains:
-one aluminium cylinder W d.46mm 3 large external transfers and 7 inside liquid black or grey
-shut up d.46mm black high compression
-a single segment piston with side greases d.46mm
-a reinforced axis treated anti wear original diameter
-2 piston clips ( spindle) type crab
-1 extra fine segments reinforced hard chrome-plated
-pack reinforced head joints-clamp screw-paper base joint
-copper exhaust joint
As an option we offer a stage 1 preparation for +/- 10 500 rpm, this preparation is a modification of the channels and the exhaust light by increasing the diagrams and improving the duct, it increases the performance of the cylinder. An improvement of the back skirt is included as well as a finish of the intake lights. Count a little extra time for this preparation! The price is due to the complexity of working the exhaust in W and the fragility of processing on these cylinders, which makes it one of the most difficult cylinders to work.
Optionally, we offer a 2 course preparation aimed at 13,000 rpm, this preparation is a modification of the channels and the exhaust light by increasing the diagrams and improving the duct, we pass on a diagram of 190°, admission side: we arrive on a diagram of 129° lateral / 128° scanning, this preparation completely metamorphoses the kit. An improvement of the back skirt and piston is also included. Very heavy preparation to accompany a carburation of 24 to 25mm, variable ignition, ultra reinforced crankshaft, variation exploiting the 13 000 / 13 500 rpm, crankcases POLINI with adaptor lock valves RRD, TPR V.FORCE valves or MALOSSI VL18 from AM6... Delivered with the right data (special extra fine head joint) for the squish and compression ratio (we aim at minimum 14:1 with this engine preparation). Count an additional time for this preparation! The price is due to the complexity of working the exhaust in W as well as the fragility of processing on these cylinders, this makes it one of the most difficult cylinders to work, on a large preparation like this one, the hours are numerous.
*On request, transfers to the base can be modified or left stock, on request, we can also adapt this preparation to the long run RRD!!!
Specific References
Reference: 204.0201/A
The luxury piston with replacement chrome segment for 70cc aluminum kits from Peugeot 103.
Reference: 206.0121
Luxury segment treated with a more pronounced doming for less friction and therefore more resistance.
Reference: 317.0102
Quality stud and reinforced to prevent breakage or wear. Maximum tightening 18nm or 2,04mk / g. In addition to this, you need to know more about it.
Reference: 272.0001
The pistol type POLINI piston clips for your axis of 12mm, material diameter of 1mm!
Reference: 209.0192
To be replaced with each dismantling, the POLINI gaskets for 70cc liquid cooling kit on PEUGEOT 103!
Reference: 315.0028
Cooling screws for POLINI kit on PEUGEOT, MINARELLI ...
Reference: 142.0088
A superb kit, 6 transfers with a W-shaped exhaust, 46mm in diameter in aluminium, power with a world-renowned kit for your 103!
Reference: 142.0100
W exhaust, liquid cooling, 6 intake transfers, mono-segment, chrome treated aluminum... What more could you ask for from a 103!
Reference: 56207.00
A very good rare and powerful kit to be accompanied by a good high compression cylinder head in Ø46mm.
Reference: 56215.00
The biggest kit on the market for 103, or should we say huge? A completely exceptional preparation base for experienced people who know how to make the engines speak!
Reference: 003200
Out of production.
Reference: KT00073
Super strong and torquey, the only 70cc kit with the ATHENA which is very well suited to crankcases with 2 transfers!
Reference: CIL-962-S
Although relatively uncommon, this kit did nothing specific.
Reference: HM44
The most powerful liquid Ø46mm kit on the market!
Reference: 31 8388
Very good kit level performance, torque and quality always at the rendezvous.
Reference: 02022546
A kit at a low price and yet very efficient in addition to being a very good basis for preparation with its exhaust has boosters, its 6 transfers and its mono-segment (or bi-segment).
Reference: 142.0089
Ideal for a small couple configuration! Original size transfers, solidity, simplicity, guaranteed performance POLINI !
Reference: 142.0086
Ideal for a coupled jam! Majorized transfers, strength, simplicity, guaranteed performance POLINI!
Reference: HM42
The monstrous S RACE 70cc for PEUGEOT 103 is finally there!!!!
Reference: CI.26.650.G
Overpowered kit on the verge of extinction. Out of production!
Reference: MF27.13201
Escape W, liquid cooling, 6 intake transfers, mono-segment, nicasil-treated aluminum... What better to ask for a 103
Reference: 56209.00
The biggest kit on the market for 103, or should we say huge? A totally out-of-the-ordinary preparation base for experienced riders who know how to make the engines talk!