
Reference: DIG6
CDI calculator housing MVT DIGIMAX 6 for ignition MVT MILLENIUM on MINARELLI AM6
Ideal for preparing your ignition and gaining additional performance.
Banner
For ignition MVT MILLENIUM EXT112 and EXT113 on MINARELLI AM6 engine
Here is a very practical case, it was invented a few years ago by Mr. Alain GODOU (former boss of AGP and now boss of MVT ignition). This case will allow you many wonders:
1-This case improves and increases the variation (more variable curve).
2-This case will offer you the choice between 3 different ignition curves.
3-This case will allow you to adjust the advance and this without dismantling.
Clearly, this case will increase the variation of the ignition, the number of degrees of offset according to the minute laps, the ignition will obviously be much more efficient. Subsequently, an ignition curve represents the variation according to the number of minute laps. For example, a coupled engine will require at best a fairly low and coupled curve while a very high speed engine will require a very pronounced curve. Here you can select the desired curve, 3 curves offer you, to change it & select, you just need to enter a combination of digits (notice and numeral combinations provide with the piece). Finally, once the curve is selected, you will be able to change the advance of the ignition (the famous ignition setting). No need for a setup and tool to change. Only a combination of numbers! For example, here is the list of combinations and their actions on ignition:
Start by ticking your ignition MVT Premium or Digital Direct has 2.9mm before high dead point (PMH). Take good care to check your carburation every test!
Code 000000= curve MVT 1 and +3° in advance
Code 100000= curve MVT 1 and +2° in advance
Code 110000= curve MVT 1 and +1° in advance
Code 111000= curve MVT 1 and +0° in advance (for example MVT Premium or Digital Direct origin)
Code 111100= curve MVT 1 and -1° in advance
Code 011100= curve MVT 1 and -2° ahead
Code 001100= curve MVT 3 and +3° ahead
Code 000100= curve MVT 3 and +2° ahead
Code 001000= curve MVT 3 and +1° in advance
Code 010000= curve MVT 3 and +0° in advance (such as the MVT Premium or Digital Direct origin)
Code 011000= curve MVT 3 and -1° ahead
Code 010100= curve MVT 3 and -2° ahead
Code 110100= curve MVT 4 and +3° ahead
Code 111110= curve MVT 4 and +2° ahead
Code 110110= curve MVT 4 and +1° in advance
Code 010010= curve MVT 4 and +0° in advance (such as the MVT Premium or Digital Direct origin)
Code 110010= curve MVT 4 and -1° ahead
Code 100010= curve MVT 4 and -2° ahead
Once you have selected the curve the appropriate advance to your engine, take good care to recheck your carburation! This small case will bring even more performance to your engine, if you are well adjusted, the gain is impressive.
Reference: DIG6
Ideal for preparing your ignition and gaining additional performance.
Reference: EPROM1
Ideal for preparing your ignition and obtaining an additional performance gain.
Reference: 169345
A real asset to prepare your original ignition and offer you guaranteed power gain!
Reference: 171.0677
24-pin unclamping CDI box for MINARELLI AM6 EURO 4, 5 mounted on various 50cc motorcycle from 2018 (and exception) such as HONDA, HM, CRE, BAJA, DERAPAGE ...
Reference: 15158
Coil with integrated CDI unbridled with 4 terminals with ground wire.
Reference: 478410
Coil with integrated CDI with 4 branches without mass.
Reference: 0 / 005.705.3880
An original RIEJU CDI box but less expensive than in concession!
Reference: 511615
24-pin unclamping CDI box for MINARELLI AM6 mounted on various 50cc motorcycles until 2017.
Reference: 180023B
Original 24-pin CDI box for MINARELLI AM6 EURO 4, 5 mounted on various 50cc motorcycles from 2018 such as HONDA, HM, CRE, BAJA, DERAPAGE ...
Reference: 5514398
Ideal replacement case in case of wear, electronic failure ... of your old part.
Reference: 506233
An original type CDI, ideal in case of malfunction of your CDI originally mounted on your AM6, DERBI SENDA, APRILIA RX, GILERA RCR ...
Reference: VCR-RD10188.E4
24-pin unclamping CDI box for MINARELLI AM6 EURO 4, 5 mounted on various 50cc motorcycle from 2018 (and exception) such as the RIEJU MRT, BETA RR, SHERCO Factory ...
Reference: RJ34/61
Cdi MVT, ideal in case of failure on your ignition MVT!
Reference: 511614
24-pin unclamping CDI box for MINARELLI AM6 EURO 4, 5 mounted on various 50cc motorcycles from 2018 (and exception) such as the RIEJU MRT, BETA RR, SHERCO Factory ...
Reference: VCR-RD10186.RB
CDI box 8 release pins for MINARELLI AM6 with DUCATI 12 coil ignition mounted on various 50cc motorcycles. Please note, not compatible with EURO 4!!!