• Banner

Crankshaft, connecting rod assembly long race for DERBI euro 3
Crankshaft, connecting rod assembly long race for DERBI euro 3

Crankshaft, connecting rod assembly long race for DERBI euro 3

Here you will find crankshafts has long race for DERBI euro 3 for motor bike 50cc DERBI SUPERMOTARD, ENDURO, DRD X-RACE, RIEJU, BETA RR YAMAHA DT, MBK X-LIMIT, XP6, Aprilia RX, MX, SX. .. and many other models. Remember, the crankshaft has long run increase the engine displacement. They are not approved, they offer a clear increase in power and torque! They can be mounted on cylinders specially designed for a long run, but also on kits 70cc or 80cc standard, with a wedge ... If diagrams allow. Here are some ideas: original -Course crankshaft derbi euro 3: 40.00mm original rod -Size: 90mm -Ø silk / worn Original roll: Ø20mm -Cage to original needle: Ø12mm X Ø15mm X Length 15mm a 47mm diameter cylinder with an original race 40mm provides the engine displacement 69,39cc and operation is very far from the square called race. A 47mm diameter cylinder with a 43mm long stroke provides the engine displacement 74,60cc and operation comes a little more than the so-called square race. A 47mm diameter cylinder with a 45mm long stroke provides the engine displacement 78,07cc and operation is very close to the square called race. Remember that a cylinder which is scheduled for a 40.00mm before being placed on a long race course must be verified, he will receive a hold of 1.5mm for a 43mm stroke for example, or a block of 2mm for a race 44mm ... and so on. The diagrams must therefore be higher! We must therefore look at the basic diagrams with standard 40.00mm race. Diagrams not to exceed are around 135/195 ° to keep a usable engine. The squish should also be checked, and for proper operation, planning work on the down lights so that the piston opens at BDC (bottom dead center)!

There are 16 products.

Showing 1-16 of 16 item(s)

Active filters

Reference: CIG-85R

BRK Competition Systems By BARIKIT

Crankshaft, connecting rod assembly BARIKIT BRK Competition long race 43mm for mécaboite driving DERBI euro 3 & 4

Well reinforced with better balance and more strength than the normal BARIKIT model. This 43mm stroke is ideal for increasing your stroke, displacement, power, torque .... With a 1.5mm shim.

Price €174.99
Shipping in 7 to 12 days depending on BARIKIT factory arrivals
More
Shipping in 7 to 12 days depending on BARIKIT factory arrivals

Reference: 9930210

TOP PERFORMANCES

Crankshaft, connecting rod TOP PERFORMANCES long stroke 44mm for mécaboite driving DERBI euro 3 & 4 (with balancer)

Special high-end 44mm long stroke connecting rod, 90mm machined forged connecting rod, ... With Ø12 mm silver treated needle cage Dynamic balancing designed to be assembled with a balancer.

Price €174.99
Shipping in 8 to 15 days depending on factory arrivals TOP PERFORMANCES
More
Shipping in 8 to 15 days depending on factory arrivals TOP PERFORMANCES

Reference: CB.12.243.2

ITALKIT

Crankshaft, ITALKIT Racing crankshaft competition 43mm long race for mécaboite driving DERBI euro 3 & 4 (without balancer)

Special high-end 43mm long stroke connecting rod, 90mm machined forged connecting rod, ... with Ø12 mm silver treated needle cage Dynamic balancing designed to be assembled without balancer.

Price €222.49
Attention, requires a period of more than 20 days!
More
Attention, requires a period of more than 20 days!